CoolShirt Systems - 2001-0005 - Mobilecool Bp 2

The Mobilecool Bp2 System Keeps You Consistently Cool And Safe Especially In A Hot Environment. Powered By 7.4v, It Is Used As A Self Contained Portable Cooling System For The Employee Providing The Portability Needed To Continue Normal Work Functions Without Being Tied Down To A Power Outlet. Consistent Use Of The System Will Help Keep The Employee Safe, Mentally Alert And Productive By Helping To Maintain A Safe Core Body Temperature While Performing Their Tasks.operating Instructions: 1. Charge The Battery Pack With The Supplied Battery Charger: a. The Battery Pack Is Located In A Pouch On The Inside Of The Backpack, At The Top b. The Battery Pack Can Be Left In Place For Charging Or Removed From Its Pouch. c. Simply Detach The Wire Terminal From The Battery Pack And Attach The Charger To The battery At The Same Terminal Location d. The First Charge Will Take Several Hours, Then A Few Hours For Subsequent Charges. A solid Green Light On The Charger Indicates The Charge Is Complete. 2. Place Endurance Ice In Freezer Until Frozen Solid. Place Endurance Ice Back In water Bladder. Note: Coolshirt Recommends Putting Ice Cubes In The bladder With Endurance Ice 3. Re-install The Battery Pack. 4. Add 1/2 Ounce Of Maintenance Additive (5003-0001) Then Fill Bladder With Enough Cold water To Cover The Pump Then Seal The Bladder. 5. Priming The System: a. On A Flat Surface Lay Out The Garment And Backpack Such That The Quick Disconnect Fittings are Facing Each Other. b. Prop Up The Backpack Such That The Water In The Bladder Settles At The Bottom Of The bladder (ie: Toward The Pump At The Bottom Of The Backpack). c. Connect The Garment And Backpack Together Using The Quick Disconnect Fittings. d. Using The Toggle Switch, Turn On The System And Allow It To Run For A Few Minutes, Taking note That The Water Coolant Is Moving Throughout The Garment. Turn The System Off And inspect The Bladder To See If It Is Filled Half-way With Water. If Not Filled Half-way, Top Off As required. 6. Close The Backpack Flap By Using The Dual Zipper Pull. 7. Putting The System On: put On The Garment And Backpack. For Optimum Cooling Performance, The Garment Should fit Snug To The Body And Be Situated Against The Skin, Beneath All Other Clothing. 8. Turn On The System Using The Toggle Switch For Cooling. If You Are Receiving Too Much cooling, Turn The System Off Using The Toggle Switch. 9. Taking The System Off: turn The System Off Using The Toggle Switch. push The Tabs On The Quick Disconnect Fittings Until They Pop Apart. remove Garment And Backpack. 10. For Extended Cooling: open The Bladder And Replace The Melted Endurance Ice With A Frozen Endurance Ice if Using Ice Cubes, Open The Bladder And Dump Excess Water. Re-fill With Ice Cubes And Top off With Water As Per Instruction 4. maintenance: 1. Laundering The Garment: a. Turn The Shirt Inside Out. b. Optional: Place In A Laundry Bag. c. Launder Or Clean The Cooling Garment Per The Care Instructions Located In The Garment packaging. 2. Cleaning The Bladder And Garment Tubing: a. If Mold Appears In The Bladder Or Garment Tubing, Pour 2 Ounces Of Liquid Maintenance additive Into A Prepared Bladder (with Endurance Ice Inserted And Topped Off With Water), then Operate The System During Your Next Cooling Cycle. b. The Maintenance Additive (5003-0001) Contains A Fungicide And Is Specially Formulated To clean And Sanitize Your Coolshirt Mobilecool Bp2. It Is Nontoxic And Biodegradable. reference Caution Below.